Security & Safety

    Reducing Flying-Glass Hazard in a Blast Event

    The objective is hazard reduction: keep glass fragments retained and anchored instead of travelling into occupied space. Performance belongs to a designed system — glass, film, attachment and frame — verified against a specific tested configuration.

    Direct answer

    How does blast mitigation film reduce injury?

    Untreated glass fails into high-velocity shards. A blast mitigation system bonds the glass to a tear-resistant film so it fails as a retained membrane, and a structural perimeter attachment keeps that membrane in the frame. Injury reduction is measured as a hazard level — how far fragments travel at a stated pressure and impulse — under standards such as ASTM F1642 and the GSA performance conditions.

    What 3M currently publishes for S2400

    3M Scotchshield Security Window Film S2400, installed with 3M Impact Protection Attachment on 1/4-inch annealed or tempered single-pane glass, is published with a GSA Rating 2 and ASTM F1642 Minimal Hazard result at 6 psi / 42 psi-msec in the current 3M Scotchshield S2400 Technical Specifications.

    Read this carefully: that result describes one specific tested configuration. It is not a blanket rating for every existing window, glass type, thickness, insulated unit or frame. Any project claim has to be tied back to a configuration the manufacturer has actually tested.

    3M also states plainly that these window films are not bulletproof and are not designed to stop intruders; they may help retain broken glass and potentially delay entry under appropriate conditions. The same specification publishes ANSI Z97.1 Class A (Unlimited) safety-glazing testing on specified 1/8-inch and 1/4-inch annealed glass — again, for those tested configurations only.

    How a blast mitigation scope gets specified

    1. 1Survey glass type, thickness and glazing configuration at every opening in scope
    2. 2Establish the threat basis with the owner or security consultant (standoff, pressure, impulse)
    3. 3Select the film and attachment combination whose tested configuration is closest to the actual conditions
    4. 4Confirm frame and sealant compatibility for a wet-glaze or profile attachment
    5. 5Document limitations in writing so nobody assumes a rating the installation does not carry

    Related systems & products

    Blast mitigation documentation

    Download the manufacturer data cards and specifications behind these systems.

    3M Bomb Blast Protection Card (image)

    Data Card (JPG)

    Attachment systems, blast testing standards, and tear-resistant film technology.

    Download

    3M IPA — Architectural Specification

    PDF Spec

    CSI-format spec section for specifying IPA on commercial projects.

    Download

    3M Forced-Entry Case Study — Retail

    PDF Case Study

    Smash-and-grab attempt stopped at the glass line on a commercial storefront.

    Download

    Blast mitigation FAQ

    What the ratings mean and where they apply

    Reduce flying-glass hazard. In a blast event most injuries come from glass fragments travelling into the occupied space. A blast mitigation system is designed to keep those fragments bonded to the film and, where an attachment is used, to keep the filmed glass anchored to the frame.

    No. There is no blanket blast rating for an existing window. A hazard rating applies only to the specific tested configuration — a defined glass type and thickness, film, attachment method and frame.

    3M publishes that Scotchshield S2400 installed with 3M Impact Protection Attachment on 1/4-inch annealed or tempered single-pane glass achieved GSA Rating 2 and ASTM F1642 Minimal Hazard at 6 psi / 42 psi-msec, per the current 3M Technical Specifications. That result belongs to that tested configuration, not to every window.

    They are hazard-level classifications from arena or shock-tube testing that describe how far glass fragments travel into a room at a defined blast pressure and impulse. They describe hazard reduction, not the absence of damage.

    For blast mitigation, yes in practice. Film alone can retain fragments while the whole glazing panel still leaves the frame. Attachment is what anchors the filmed lite to the frame.

    Yes. We regularly work nights and weekends on occupied government, healthcare and institutional buildings across Delaware and the Maryland Eastern Shore.

    Next step

    Request a blast hazard assessment

    We document the glass, frames and realistic options before anything is specified.

    Security glazing · Shore Tint & More

    Compare the complete system

    Film, glass, attachment and frame determine what can be specified for an opening.

    Schedule a Shore Glazing Survey